Veneer Roller Dryer Machine
Type: Roller Veneer Dryer
Working Width: 3m
Veneer thickness: 0.6-8mm
Heating Area Length: 44m
Drying capacity (m³/24h): 70-80cbm
Veneer Water Moisture: Down to 10%
Cost: 6-12$/m3 (Labor+Fuel+Electricity)
Heat Source: Biomass Burner (Other options available)
Veneer Roller Dryer Machine
Veneer dryer is used in wood processing industry. The moisture content of veneer after rotary cutting is very high, and the veneer must be dried to meet the requirements of gluing process. Therefore, the veneer after rotary cutting needs to be dried naturally or dried by using the veneer dryer before it can be used.
Working principle of Veneer Dryer：
Shine Biomass Veneer dryer is product in the design of the continuous roller pressure type of hot air cylinder,it is using the most advanced continuous pressurized contact and its working principle is veneer veneer drying technology in steel tube under the clamping roller, two by preheating the oven temperature to 140, and then enter the upper and lower roller and through the hot air pipe to the single board upside down between hot high pressure blowing for quick dry, so you can make the veneer smooth moisture content after drying of uniform, And it has the characteristics of high temperature roller and wet veneer direct contact heat transfer, high thermal efficiency and small thermal loss.
Advantages of Shine Veneer Roller Dryer
Lowest Drying Cost、Perfect Drying Effect
According to the actual calculation, The composite cost is only about $6-12/cubic meter, including labor, electricity and fuel costs. The veneer after drying has uniform moisture content, flat, no buckle or end waviness; free of splits and the surface is in good condition for gluing.
Automatic Temperature Control System and Heat Exchange System
Control cabinet built-in automatic temperature control speed control system, can accurately control the final moisture content. Simple operation and low failure rate.Step by step heat exchange, each section of the heat exchanger specifications are different, hot air in the heat exchanger can be evenly distributed to the board; Ensure uniform drying of veneer.
Energy saving, Environmental Protection and High Efficiency
The hot air fan and the cold air fan of the dryer use the latest axial flow fan, which reduces the power consumption and greatly reduces the power of the whole machine, which can further reduce the user's later operation cost. Meet the requirements of environmental protection, good working conditions, high safety, simple operation, low failure rate.
Patented Product——Biomass Burner
It can burn all kinds of waste wood directly to reduce the drying cost mostly. Compared to steam type or heat conduction oil type veneer dryer, the drying cost is reduced greatly.
Product Parameters of 48 m Veneer Dryer Machine
Model No | GTH30-48 |
Working Width | 3m |
Deck | 2 |
Heating area length | 44m |
Cooling area length | 4m |
Veneer thickness | 0.6-8mm |
Veneer water moisture | Fresh veneer to about 10% |
Heating material & drying temperature | Waste wood, 140-200℃C adjustable. There is automatic temperature control and speed regulation system, which can guarantee the moisture content is consistent. |
Drying capacity (m³/day) | 70-80cbm |
Veneer transport speed | 5-22m/min，16A chain |
Hot air blower | Power:5.5KW（11pc） |
Traction motor | Power: 7.5KW，frequency control（2pc） |
Cold air blower | Power: 5.5KW（1pc） |
Air intake fan | Power : 11KW（2pc） |
6 ton biomass burner | Power: 16.5KW |
Total power | 119.5KW |
Actual electricity consumption | About 130kwh per hour |
Veneer Dryer of Case Video
Certification
The customer evaluation
Shine Factory
Our Services
Pre-sale services:
1) Provide the free consultation of all Core Veneer Dryer Machine.
2) According to the clients' special requirement, offering the reasonable plan and free design to help to select the equipment.
3) Welcome to visit our factory.
Services during the sales:
1) Inspect the machine before leaving the factory.
2) Overseas install and debug the equipment.
3) Train the first-line operator.
After sale services:
1) 24 hours online service（WhatsApp：+8615806625431）
2) Provide the VIDEO with Install and debug the equipment.
3) Provide technical exchanging（Technical phone：15665878109）Door to door service is possible.
Packaging & Shipping
