Veneer Roller Dryer Machine-manufacture,factory,supplier from China

1. Operating system:The planed (rotary) veneer is fed from the feed port of the wind-jet roller type veneer dryer, and through the relative rotation of several pairs of upper and lower rollers inside the dryer, the planed and rotary-cut veneer is rotated in the predetermined direction. Front running, during the veneer traveling process, the hot air of 110-150 degrees Celsius is vertically sprayed to the upper and lower surfaces of the veneer at the wind speed of V=1.5M/S through the air nozzle installed between the two pairs of rollers.

Our veneer drying equipment purchased by the customer is being installed under the guidance of our engineers.After the installation and test machine,the customer feedback is very good,and they are very satisfied with our equipment.Thank customers for their trust in us.

The veneer dryer is mainly used for drying veneer and is the main machine for producing plywood. Due to the high moisture content inside the newly rotary-cut veneer, the purpose of the equipment is to reduce the moisture content of the veneer to meet the requirements, while reducing material loss. The equipment has the characteristics of high thermal efficiency and small heat loss, which can effectively improve the work efficiency and the quality of plywood products. However, there are a few things to be aware of when using the device.Precautions for the use of veneer dryers1.

The 4 deck veneer dryer purchased by the Myanmar factory is used to dry rubber wood,and the customer feedback is very good,it is used with a biomass burner.The biomass burner acts as a heat source,providing high temperature to the dryer to ensure enough heat to effectively impact the wet veneer.At the same time,the bark of the peeling machine and the waste veneer of the rotary cutter are directly incinerated as fuel,which solves the problem of waste accumulation in the veneer plywood factory.veneer dryer video

Recently, the 2 deck roller veneer dryer purchased by our Vietnamese customer has been installed and successfully tested and operated normally. The engineers have trained the workers to operate the veneer dryer skillfully before returning. We welcome you to visit the case site. The veneer dryer is equipped with a biomass burner, which directly burns the bark, saving fuel costs. It uses a new axial flow fan, which reduces power consumption and greatly reduces the power of the whole machine, which can further reduce the user's later operating costs.

The roller veneer dryer can dry various types of veneers, including softwood, hardwood, bamboo, etc. (such as some common wood types such as eucalyptus, birch, poplar, pine, spruce, oak, maple, Walnut, teak, etc.). It should be noted that different types of wood have different fiber structures, densities, moisture content and other characteristics. Therefore, when using a roller veneer dryer to dry wood, it is necessary to set appropriate parameters according to the characteristics of different wood to ensure Drying results and quality. and perform proper maintenance and upkeep on the machine.

The GTH45-50 four-layer biomass roller dryer purchased by our South African customer is currently being installed. It is installed under the guidance of our technicians at the customer's factory. Using new technology, the power of the whole machine has been reduced by 38%, and the production Material burners can burn bark and black bark, saving fuel costs. If you also have needs, please feel free to contact us!

The 40m 2 deck veneer dryer purchased by an Indonesian customer has now been installed and is being debugged.Due to the epidemic,we could not send someone to guide the installation.The customer successfully installed it in our video and chat communication instructions.Thank you very much for your support Our biomass burner,which can directly burn all kinds of waste wood,saves fuel efficiently; it adopts automatic control and frequency conversion control system,which can automatically adjust the transmission speed and To achieve the ideal drying effect,if you are interested in our machine,pleas

The 2 deck roller veneer dryer is equipped with a 6-ton biomass burner, which produces more than 70 cubic meters per day. It is being installed in Russia.

The customer factory reported that the veneers dried by the veneer dryer used in the past would have cracking problems. What is the cause of this phenomenon?This is likely to involve the internal structure of the dryer and the stability of the dryer operation. Come and see.The spacing between the rollers of the veneer drying. Technically speaking, the roller spacing from the axis to the axis of the 4 deck roller dryer is 330mm. The upper and lower air ducts are laid between the front and rear rollers.