Veneer Dryer Temperature Controller-manufacture,factory,supplier from China

The 4 deck veneer dryer purchased by the Myanmar factory is used to dry rubber wood,and the customer feedback is very good,it is used with a biomass burner.The biomass burner acts as a heat source,providing high temperature to the dryer to ensure enough heat to effectively impact the wet veneer.At the same time,the bark of the peeling machine and the waste veneer of the rotary cutter are directly incinerated as fuel,which solves the problem of waste accumulation in the veneer plywood factory.veneer dryer video

Veneer dryers generally need to make preparations before the official test run to ensure that the test run can proceed normally. The preparation work required before the test run mainly includes the following points:Warming furnace: The high-temperature-resistant material poured into the burner is very thick, and the moisture in the furnace needs to be dried out so that it can be used easily in the future. Pay special attention to avoid rapid fire. Fuel: Log wood, white bark of branches, etc.

Veneer dryers generally need to make preparations before the official test run to ensure that the test run can proceed normally. The preparation work required before the test run mainly includes the following points:First, warm the furnace: The high-temperature-resistant material poured into the burner is very thick and needs to be dried out of the moisture in the furnace so that it can be used easily in the future. Pay special attention to avoid rapid fire. Fuel: Log wood, white bark of branches, etc.

The shine veneer dryer has the characteristics of large drying output, good effect, and easy maintenance. It has been unanimously recognized by customers and has been widely used. However, some customers always report that the efficiency of the wood chip drying equipment is not high. This is due to insufficient It is caused by paying attention to the details in the work. So what are the precautions when using veneer drying equipment?We always hope that the veneer can dry quickly, so we set the temperature to be very high and the temperature rises very quickly.

The Latvian customer bought our 4 deck veneer dryer and biomass burner, which is automatic board loading and semi-automatic board collecting to save labor cost, and the dried veneer is smooth without wrinkles, with good effect. We have a professional r & D team, can design different models according to the special requirements of customers, if you need to feel free to contact us.

After purchasing one of our veneer dryers, our Zimbabwean customers have recently purchased a second veneer dryer , which is currently being installed, along with our biomass burners, by our engineers The installation is carried out under the guidance, and the customer feedback is very good. If there is a need in the future, we will continue to buy our equipment. Thank you for your trust in us.

Many people may encounter the problem of veneer jamming when using the roller veneer dryer. In order to avoid this problem, the following suggestions can be taken: First, keep the equipment clean, clean the dust collector and exhaust duct, and minimize the accumulation of dust; second, do a good job of adjusting the equipment, reduce the friction and wear of the equipment, and regularly check the status of the roller bearings; finally, pay attention to the control of drying temperature and humidity to avoid excessive temperature and humidity, which will cause veneer deformation and jamming.

Recently, due to the impact of the epidemic, many customers were unable to go to the site to see the equipment. We organized an online viewing site, and our engineer gave a comprehensive explanation of the veneer dryer in live video. Finally, the questions raised by customers were all Answer one by one, if you also want to see the scene of equipment operation, please feel free to contact us.

The veneer needs to be dried before use, so that the wood will not be prone to problems in future use, and the dried board will be easier to preserve. Let's take a look at how a dryer works.Wood veneers are processed and divided into boards of equal thickness before entering the dryer. After entering the inside of the machine, it is heated and evaporated. Adopt high temperature and rapid drying construction technology. The treated boards are less prone to cracks and deformation problems.

The veneer dryer is mainly used for drying veneer and is the main machine for producing plywood. Due to the high moisture content inside the newly rotary-cut veneer, the purpose of the equipment is to reduce the moisture content of the veneer to meet the requirements, while reducing material loss. The equipment has the characteristics of high thermal efficiency and small heat loss, which can effectively improve the work efficiency and the quality of plywood products. However, there are a few things to be aware of when using the device.Precautions for the use of veneer dryers1.