Temperature Controller-manufacture,factory,supplier from China

The 4 deck veneer dryer purchased by the Myanmar factory is used to dry rubber wood,and the customer feedback is very good,it is used with a biomass burner.The biomass burner acts as a heat source,providing high temperature to the dryer to ensure enough heat to effectively impact the wet veneer.At the same time,the bark of the peeling machine and the waste veneer of the rotary cutter are directly incinerated as fuel,which solves the problem of waste accumulation in the veneer plywood factory.veneer dryer video

Veneer dryers generally need to make preparations before the official test run to ensure that the test run can proceed normally. The preparation work required before the test run mainly includes the following points:Warming furnace: The high-temperature-resistant material poured into the burner is very thick, and the moisture in the furnace needs to be dried out so that it can be used easily in the future. Pay special attention to avoid rapid fire. Fuel: Log wood, white bark of branches, etc.

Veneer dryers generally need to make preparations before the official test run to ensure that the test run can proceed normally. The preparation work required before the test run mainly includes the following points:First, warm the furnace: The high-temperature-resistant material poured into the burner is very thick and needs to be dried out of the moisture in the furnace so that it can be used easily in the future. Pay special attention to avoid rapid fire. Fuel: Log wood, white bark of branches, etc.

The shine veneer dryer has the characteristics of large drying output, good effect, and easy maintenance. It has been unanimously recognized by customers and has been widely used. However, some customers always report that the efficiency of the wood chip drying equipment is not high. This is due to insufficient It is caused by paying attention to the details in the work. So what are the precautions when using veneer drying equipment?We always hope that the veneer can dry quickly, so we set the temperature to be very high and the temperature rises very quickly.

Many people may encounter the problem of veneer jamming when using the roller veneer dryer. In order to avoid this problem, the following suggestions can be taken: First, keep the equipment clean, clean the dust collector and exhaust duct, and minimize the accumulation of dust; second, do a good job of adjusting the equipment, reduce the friction and wear of the equipment, and regularly check the status of the roller bearings; finally, pay attention to the control of drying temperature and humidity to avoid excessive temperature and humidity, which will cause veneer deformation and jamming.

The veneer needs to be dried before use, so that the wood will not be prone to problems in future use, and the dried board will be easier to preserve. Let's take a look at how a dryer works.Wood veneers are processed and divided into boards of equal thickness before entering the dryer. After entering the inside of the machine, it is heated and evaporated. Adopt high temperature and rapid drying construction technology. The treated boards are less prone to cracks and deformation problems.

African veneer bosses often ask me, why is the veneer that is baked in a dryer so damp? To answer this question, there are two main reasons:1. Water absorption of wood itselfWood has a certain range of moisture content, which is adjusted with changes in ambient temperature and humidity. Even after drying, some moisture will still remain in the wood. If the humidity in the storage environment is high, the wood will absorb the surrounding moisture, causing the moisture content to rise, resulting in moisture return.2.

Shine veneer dryers are available with outputs ranging from a dozen cubic meters to more than a hundred cubic meters. They have their own heat source biomass burner; they can directly burn waste bark to save fuel costs (it can also be used with other heat sources). The newly upgraded dryer reduces the power of the whole machine by 38%, achieving true energy saving. The automatic control system is adopted to automatically adjust the transmission speed and temperature according to different veneer thickness and moisture content to achieve the ideal drying effect.

As the main equipment for drying wood, the veneer dryer's drying speed will directly affect the quality and efficiency of drying veneers. Therefore, we must fully understand the factors that affect the drying speed in order to make it better. play a role.One of the main factors that affects the drying speed of the veneer dryer is temperature. The increase in temperature can accelerate the evaporation of moisture on the surface of the wood, so the drying of the wood will also be accelerated.

The 2 deck veneer dryer with biomass burner is currently in operation. It is used to dry rubber wood. It adopts full automatic control and frequency conversion control system. It can automatically adjust the transmission speed and temperature according to the thickness and moisture content of different veneers to achieve the ideal drying effect and accurately control the final moisture content. It avoids the phenomenon that a large number of veneers are over-dried or dried to meet the process requirements. The dried veneer is flat and wrinkle-free. We welcome you to visit the case site.