Temperature Sensor for Veneer Dryer-manufacture,factory,supplier from China

The veneer dryer is mainly used for drying veneer and is the main machine for producing plywood. Due to the high moisture content inside the newly rotary-cut veneer, the purpose of the equipment is to reduce the moisture content of the veneer to meet the requirements, while reducing material loss. The equipment has the characteristics of high thermal efficiency and small heat loss, which can effectively improve the work efficiency and the quality of plywood products. However, there are a few things to be aware of when using the device.Precautions for the use of veneer dryers1.

In 2020,a friend from Singapore successfully cooperated with us.This is a friend from a long time ago.After adding our contact information,he became very interested in our veneer dryer,but he was worried about the output of the machine.never negotiated a cooperation,and finally,after visiting our factory,the customer dispelled his concerns and showed great interest in our patented biomass burning furnace,because this furnace can reasonably use the scraps from the rotary cutting Combustion,rational use of resources,and will not produce environmental pollution,smog and other effects,and finally

The shine veneer dryer has the characteristics of large drying output, good effect, and easy maintenance. It has been unanimously recognized by customers and has been widely used. However, some customers always report that the efficiency of the wood chip drying equipment is not high. This is due to insufficient It is caused by paying attention to the details in the work. So what are the precautions when using veneer drying equipment?We always hope that the veneer can dry quickly, so we set the temperature to be very high and the temperature rises very quickly.

Shine Machinery Co., Ltd. held a two-day centralized training for company members on August 12, 2022. The training contents include product performance sorting of Shine biomass veneer dryer, business speech training, after-sales service process, etc. Each business manager presents in the form of mind map. The atmosphere on the site was warm. The senior engineer explained the relevant contents and actively interacted with the colleagues participating in the training. The training is in the form of knowledge competition with awards, and finally the general manager gives awards.

The 4 deck veneer dryer purchased by the Myanmar factory is used to dry rubber wood,and the customer feedback is very good,it is used with a biomass burner.The biomass burner acts as a heat source,providing high temperature to the dryer to ensure enough heat to effectively impact the wet veneer.At the same time,the bark of the peeling machine and the waste veneer of the rotary cutter are directly incinerated as fuel,which solves the problem of waste accumulation in the veneer plywood factory.veneer dryer video

After purchasing one of our veneer dryers, our Zimbabwean customers have recently purchased a second veneer dryer , which is currently being installed, along with our biomass burners, by our engineers The installation is carried out under the guidance, and the customer feedback is very good. If there is a need in the future, we will continue to buy our equipment. Thank you for your trust in us.

These are two sets of 2 deck veneer dryers from our old South African customer.They were installed and guided by our engineers.The customer was very satisfied after buying one of our machines,and then bought the second one.Now Both are in normal use, and the customer feels that the equipment is very good,and the operation is convenient,and the dried veneer is very flat.We are very grateful to South African users for their support.We will continue to work hard in the process of research and development and production to complete the task with quality and quantity.We are also very welcome to vis

Veneer dryers generally need to make preparations before the official test run to ensure that the test run can proceed normally. The preparation work required before the test run mainly includes the following points:Warming furnace: The high-temperature-resistant material poured into the burner is very thick, and the moisture in the furnace needs to be dried out so that it can be used easily in the future. Pay special attention to avoid rapid fire. Fuel: Log wood, white bark of branches, etc.

Veneer dryers generally need to make preparations before the official test run to ensure that the test run can proceed normally. The preparation work required before the test run mainly includes the following points:First, warm the furnace: The high-temperature-resistant material poured into the burner is very thick and needs to be dried out of the moisture in the furnace so that it can be used easily in the future. Pay special attention to avoid rapid fire. Fuel: Log wood, white bark of branches, etc.

Recently, the double-layer dryer ordered by our customers has been completed and is ready for delivery. It is equipped with a biomass burner and can directly burn bark. The output can reach 80 cubic meters. It is used to dry rubber wood veneers. Before placing an order, the customer went to another customer's site for a field inspection and was very satisfied with the equipment. After that, he decided to purchase it.