Smart-Control Plywood Veneer Dryer-manufacture,factory,supplier from China

The veneer dryer is mainly used for drying veneer and is the main machine for producing plywood. Due to the high moisture content inside the newly rotary-cut veneer, the purpose of the equipment is to reduce the moisture content of the veneer to meet the requirements, while reducing material loss. The equipment has the characteristics of high thermal efficiency and small heat loss, which can effectively improve the work efficiency and the quality of plywood products. However, there are a few things to be aware of when using the device.Precautions for the use of veneer dryers1.

The 40m 2 deck veneer dryer purchased by an Indonesian customer has now been installed and is being debugged.Due to the epidemic,we could not send someone to guide the installation.The customer successfully installed it in our video and chat communication instructions.Thank you very much for your support Our biomass burner,which can directly burn all kinds of waste wood,saves fuel efficiently; it adopts automatic control and frequency conversion control system,which can automatically adjust the transmission speed and To achieve the ideal drying effect,if you are interested in our machine,pleas

The 4 deck veneer dryer purchased by the Myanmar factory is used to dry rubber wood,and the customer feedback is very good,it is used with a biomass burner.The biomass burner acts as a heat source,providing high temperature to the dryer to ensure enough heat to effectively impact the wet veneer.At the same time,the bark of the peeling machine and the waste veneer of the rotary cutter are directly incinerated as fuel,which solves the problem of waste accumulation in the veneer plywood factory.veneer dryer video

The Latvian customer bought our 4 deck veneer dryer and biomass burner, which is automatic board loading and semi-automatic board collecting to save labor cost, and the dried veneer is smooth without wrinkles, with good effect. We have a professional r & D team, can design different models according to the special requirements of customers, if you need to feel free to contact us.

The 2 deck veneer dryer with biomass burner is currently in operation. It is used to dry rubber wood. It adopts full automatic control and frequency conversion control system. It can automatically adjust the transmission speed and temperature according to the thickness and moisture content of different veneers to achieve the ideal drying effect and accurately control the final moisture content. It avoids the phenomenon that a large number of veneers are over-dried or dried to meet the process requirements. The dried veneer is flat and wrinkle-free. We welcome you to visit the case site.

After purchasing one of our veneer dryers, our Zimbabwean customers have recently purchased a second veneer dryer , which is currently being installed, along with our biomass burners, by our engineers The installation is carried out under the guidance, and the customer feedback is very good. If there is a need in the future, we will continue to buy our equipment. Thank you for your trust in us.

1. Operating system:The planed (rotary) veneer is fed from the feed port of the wind-jet roller type veneer dryer, and through the relative rotation of several pairs of upper and lower rollers inside the dryer, the planed and rotary-cut veneer is rotated in the predetermined direction. Front running, during the veneer traveling process, the hot air of 110-150 degrees Celsius is vertically sprayed to the upper and lower surfaces of the veneer at the wind speed of V=1.5M/S through the air nozzle installed between the two pairs of rollers.

Recently, customers from Thailand visited the shine veneer dryer factory to inspect our veneer drying equipment. During the inspection, the customer learned in detail about the production process, operation principle and technical advantages of the equipment, and highly praised our production strength and quality control system.Accompanied by the technical team, the customer visited the dryer production line and watched the actual operation of the equipment.

The production process of plywood is a multi-step process involving raw material processing, veneer production, gluing and pressing, and post-processing. Here are the main production processes:1. Log processingCut: Cut logs into lengths suitable for peeling or planing (usually 2.6 meters or customized sizes).Debarking: Remove bark to reduce the impact of impurities on subsequent processes.Cooking and softening (optional): Soak or cook logs (temperature about 60-80℃) to soften wood fibers for peeling.2.

After the on-site drying test, the shrinkage rate of the veneer before and after drying by Shine veneer dryer is 2-2.5 cm, and the moisture content can be dried to zero, or it can be dried to the moisture you need according to your requirements. It adopts automatic control and frequency conversion control system, which can automatically adjust the transmission speed and temperature according to different veneer thickness and moisture content, so as to achieve the ideal drying effect. Biomass burners can directly burn all kinds of waste wood, saving drying costs.