plywood veneer roller dryer machine-manufacture,factory,supplier from China

The veneer dryer is mainly used for drying veneer and is the main machine for producing plywood. Due to the high moisture content inside the newly rotary-cut veneer, the purpose of the equipment is to reduce the moisture content of the veneer to meet the requirements, while reducing material loss. The equipment has the characteristics of high thermal efficiency and small heat loss, which can effectively improve the work efficiency and the quality of plywood products. However, there are a few things to be aware of when using the device.Precautions for the use of veneer dryers1.

The 4 deck veneer dryer purchased by the Myanmar factory is used to dry rubber wood,and the customer feedback is very good,it is used with a biomass burner.The biomass burner acts as a heat source,providing high temperature to the dryer to ensure enough heat to effectively impact the wet veneer.At the same time,the bark of the peeling machine and the waste veneer of the rotary cutter are directly incinerated as fuel,which solves the problem of waste accumulation in the veneer plywood factory.veneer dryer video

1. Operating system:The planed (rotary) veneer is fed from the feed port of the wind-jet roller type veneer dryer, and through the relative rotation of several pairs of upper and lower rollers inside the dryer, the planed and rotary-cut veneer is rotated in the predetermined direction. Front running, during the veneer traveling process, the hot air of 110-150 degrees Celsius is vertically sprayed to the upper and lower surfaces of the veneer at the wind speed of V=1.5M/S through the air nozzle installed between the two pairs of rollers.

Our veneer drying equipment purchased by the customer is being installed under the guidance of our engineers.After the installation and test machine,the customer feedback is very good,and they are very satisfied with our equipment.Thank customers for their trust in us.

The newly upgraded plywood dryer machine mainly has the following features:1. Heat exchange systemShine heat exchangers adopt step-by-step heat exchange. The specifications of the heat exchangers in each section are different. The hot air in the heat exchanger can be evenly distributed to the single board. The dried veneer has a uniform moisture content, is smooth, has no wrinkles or end ripples, no cracks, and the surface is in good bonding condition, which fully improves energy utilization and saves unnecessary energy waste.2.

Recently, the 2 deck roller veneer dryer purchased by our Vietnamese customer has been installed and successfully tested and operated normally. The engineers have trained the workers to operate the veneer dryer skillfully before returning. We welcome you to visit the case site. The veneer dryer is equipped with a biomass burner, which directly burns the bark, saving fuel costs. It uses a new axial flow fan, which reduces power consumption and greatly reduces the power of the whole machine, which can further reduce the user's later operating costs.

The roller veneer dryer can dry various types of veneers, including softwood, hardwood, bamboo, etc. (such as some common wood types such as eucalyptus, birch, poplar, pine, spruce, oak, maple, Walnut, teak, etc.). It should be noted that different types of wood have different fiber structures, densities, moisture content and other characteristics. Therefore, when using a roller veneer dryer to dry wood, it is necessary to set appropriate parameters according to the characteristics of different wood to ensure Drying results and quality. and perform proper maintenance and upkeep on the machine.

The GTH45-50 four-layer biomass roller dryer purchased by our South African customer is currently being installed. It is installed under the guidance of our technicians at the customer's factory. Using new technology, the power of the whole machine has been reduced by 38%, and the production Material burners can burn bark and black bark, saving fuel costs. If you also have needs, please feel free to contact us!

The Latvian customer bought our 4 deck veneer dryer and biomass burner, which is automatic board loading and semi-automatic board collecting to save labor cost, and the dried veneer is smooth without wrinkles, with good effect. We have a professional r & D team, can design different models according to the special requirements of customers, if you need to feel free to contact us.

Many people do not know how to maintain the dryer to extend its service life. Let us take you to understand the daily maintenance of the dryer.1. Clean the inside and outside of the dryer regularly to ensure good ventilation and smooth hot air flow.2. Check the connections and components of the electrical system to see if the components are damaged, aged or loose. If necessary, repair or replace the problematic parts.3. Regularly check the fasteners, belts and chains of the drive system, lubricate and replace necessary parts.4.