Plywood Veneer Machine-manufacture,factory,supplier from China

The veneer dryer is mainly used for drying veneer and is the main machine for producing plywood. Due to the high moisture content inside the newly rotary-cut veneer, the purpose of the equipment is to reduce the moisture content of the veneer to meet the requirements, while reducing material loss. The equipment has the characteristics of high thermal efficiency and small heat loss, which can effectively improve the work efficiency and the quality of plywood products. However, there are a few things to be aware of when using the device.Precautions for the use of veneer dryers1.

The 4 deck veneer dryer purchased by the Myanmar factory is used to dry rubber wood,and the customer feedback is very good,it is used with a biomass burner.The biomass burner acts as a heat source,providing high temperature to the dryer to ensure enough heat to effectively impact the wet veneer.At the same time,the bark of the peeling machine and the waste veneer of the rotary cutter are directly incinerated as fuel,which solves the problem of waste accumulation in the veneer plywood factory.veneer dryer video

Our veneer drying equipment purchased by the customer is being installed under the guidance of our engineers.After the installation and test machine,the customer feedback is very good,and they are very satisfied with our equipment.Thank customers for their trust in us.

The newly upgraded plywood dryer machine mainly has the following features:1. Heat exchange systemShine heat exchangers adopt step-by-step heat exchange. The specifications of the heat exchangers in each section are different. The hot air in the heat exchanger can be evenly distributed to the single board. The dried veneer has a uniform moisture content, is smooth, has no wrinkles or end ripples, no cracks, and the surface is in good bonding condition, which fully improves energy utilization and saves unnecessary energy waste.2.

The 40m 2 deck veneer dryer purchased by an Indonesian customer has now been installed and is being debugged.Due to the epidemic,we could not send someone to guide the installation.The customer successfully installed it in our video and chat communication instructions.Thank you very much for your support Our biomass burner,which can directly burn all kinds of waste wood,saves fuel efficiently; it adopts automatic control and frequency conversion control system,which can automatically adjust the transmission speed and To achieve the ideal drying effect,if you are interested in our machine,pleas

Recently, our company successfully completed the installation and commissioning of a 2 deck veneer dryer customized by Thailand customers. The veneer dryer installed this time was customized by our company according to the needs of Thailand customers. Compared with traditional veneer dryers, it can significantly increase production capacity and effectively reduce energy consumption.

During the 5th Siva International Wood Industry Exhibition, Shamorin, chairman of the board of directors of the Russian Segezha Group, said that Russia has shifted its exports from the West to Asia, mainly China.Shamorin said: "Most of the directions of exports have been adjusted. This mainly involves pulp and paper products and plywood, while sawn timber has been supplied to China for a long time. We plan to display all the group's products in China and develop sales channels. The Segezha Group has its own forest resources and is developing service directions.

Gabon is experiencing a rainy season, which is affecting the operation of timber factories in inland areas.  During the rainy season, Gabonese veneer and plywood factories can continue to produce, but due to the impact of the rainy season, the inventory of logs has decreased, especially the inventory of Augustan logs, which has decreased significantly.Meanwhile, China's demand for African timber is on the rise.

In the production of plywood, there is an important process. Although we cannot see its effect with the naked eye, it has a vital impact on the quality of the board. It is veneer drying. Why do veneers need to be dried? This is mainly because before the peeling process, in order to soften the wood, improve its plasticity and the quality of veneer peeling, the wood segments usually undergo hydrothermal treatment, resulting in a high moisture content of the veneer after peeling.

The installation of the 2 deck veneer dryer purchased by another of our customers has been completed! This wood veneer dryer is equipped with our biomass burner, which saves fuel costs and uses new technology to save energy and electricity. Our engineers will go to the customer's factory to guide the installation. The engineers will not return until the test machine is completed and normal operation occurs. The dried boards are smooth and wrinkle-free.