Product Introduction of 26 m Face Veneer Mesh Belt DryerFor the thin veneer, the face veneer mesh belt dryer will be more suitable.The mesh belt veneer dryer is used for drying veneers with rotary cutting and slicer and it is designed especially to dry the very thin face veneer typically at 0.2-1.2mm thickness. The drying capacity of 26m 2deck veneer dryer can achieve 1.5-2m³/h. The veneer after drying is flat, moisture content is up to national standard.
Contact Now
Product Description of 30 m 3 Deck Veneer Mesh Belt Dryer30 m 3 deck veneer mesh belt dryer is important machine in plywood processing. When you peeling get fresh veneer, for long stock, need remove water and moisture, so you need core veneer dryer or drying line. Shine 3 deck veneer dryers have the salient features of higher price performance ratio, higher drying capacity. 30m 3 deck mesh belt dryer is suitable for drying thin face veneer, which can dry about 2.7m³ veneer per hour.
Contact Now
Product Description of 20 m 1 Deck Mesh Belt Dryer Machine20 m 1 deck mesh belt dryer machine is a closed-belt dryer. Its feature is that only the feed end and the discharge end are open, and the others are closed. Hot air flows through the equipment and the heat loss is low, which can save a lot of energy.
Contact Now
Product Introduction of 20 m Continuous Mesh Belt Veneer DryerThe mesh belt veneer dryer adopts 304 stainless steel to reduce the pollution of veneer, which is one of the main equipment in plywood production used to dry the veneer with thickness under 1.5mm. Hot air passes through the veneer, vaporizes the moisture of the veneers, and part of the wet steam is discharged from the box, and the other part is recycled. So it can improve the heat utilization rate.
Contact Now
Jet box is made of galvanized plate including many nozzles. The waste wood chips are burned inside the biomass burner to generate the smoke and flue gas. The high temperature smoke and flue gas is blown to the flue gas channel and heat exchangers by the induced draft fans located on the two ends of the dryer. And the flue gas channel and heat exchangers became very hot. Then hot air fans collect the hot clean air emitted from the heat exchangers and blow to the jet boxes /air tubes and finally to the top and bottom of the moving veneer. In this way, the veneer is dried.
Contact Now
Mesh Belt Veneer DryerThe mesh belt veneer jet dryer machine is usually used for drying continuous ribbons before cutting. The mesh belt veneer dryer is designed especially for the face veneer with a thickness of 0.2-1mm. The equipment is flexible in configuration, and there are many materials for drying at one time, and it can be continuously produced and dried, which is convenient to use and greatly reduces labor.Features of Mesh Belt Veneer Dryer1.
Contact Now
Veneer Mesh Belt DryerThe veneer mesh belt dryer is designed to handle the drying process of face veneer, back veneer and long core veneer.For process the surface veneer and long core veneer, this veneer dryer can avoid the break of the veneer, then can raise the veneer utilization ratio and production output.All outfitted air blower and screen are the high quality production, so it can increase the durability and useful life of the machine.We can design the machine upon our customer`s requirement.Product Parameters of Veneer Mesh Belt Dryer1.
Contact Now
Mesh belt dryer is a closed-belt dryer. Its feature is that only the feed end and the discharge end are open, and the others are closed. Hot air flows through the equipment and the heat loss is low, which can save a lot of energy. The equipment is flexible in configuration, and there are many materials for drying at one time, and it can be continuously produced and dried, which is convenient to use and greatly reduces labor.
Contact Now
Roll Jet Veneer DryerThe roller veneer dryer line has a variety of different drying configurations to suit a variety of drying needs are available. The length, width, and layers of the core veneer dryer can be designed and made for customers. The veneer roller dryer machine is durable in use and long service life. Shine Machinery is responsible for providing users the best drying solutions, not just the roll jet veneer dryer itself to ensure the higher drying capacity, energy efficiency, and less fuel cost.
Contact Now
Veneer Jet Dryer MachineVeneer jet dryer machine has the advantages of simple operation,safety and practicality, stable operation and easy maintenance ,hot pressing-leveling-drying are finished at the same time &and others.The roller dryer machine is mainly used in plywood industry, and used to remove moisture from the veneer.The dryer machine can effectively use various resources and occupy a small area.The roller dryer machine can be divided into two parts: heating section and cooling section.The heat medium can be oil and heat steam. working principle：working principle is ven
Contact Now
Mesh Belt DryerFor the thin veneer, the stainless steel mesh belt dryer will be more suitable. The mesh belt veneer dryer is used for drying veneers with rotary cutting and slicer and it is designed specially to dry the very thin face veneer typically at 0.2-1.2mm thickness. The drying capacity of 26m 2deck veneer dryer can achieve 1.5-2m³/h. The veneer after drying is flat, the moisture content is up to national standard.
Contact Now
continuous mesh belt dryerThe continuous mesh belt dryer which is one of the main equipment in veneer and plywood production and can be used for continuous drying operation. It is used for drying veneers with rotary cutting and slicer and it is designed especially to dry the very thin face veneer typically at 0.2-1.2mm thickness. It is composed of four parts, which are divided into feeding area, heating area, cooling area and discharging area.
Contact Now
The mesh belt dryer is a highly efficient hot air drying equipment designed for face and veneer. It uses a mesh belt conveyor system to evenly distribute the veneer on the mesh belt and dry it through continuous hot air flow. This design not only ensures uniform dryingof the veneer, but also greatly improves production efficiency.
Contact Now
2 Deck Jet Roller Veneer DryerShine veneer dryer adopts automatic electric control and frequency conversion system, which can adjust the transmission speed and temperature automatically according to different veneer thickness and moisture content to achieve and ideal drying effect.
Contact Now
Jet Roller Veneer DryerJet roller veneer dryer was equipped with automatic feeder device can feed the veneer to dryer and save labor cost mostly. The veneer after drying has uniform moisture content and it is flat without buckle or end waviness. Less maintenance is required for Shine veneer dryer machine and no veneer jamming leading to less downtime.
Contact Now
Roller Veneer Jet Dryerveneer dryer machine equipped with new technology and advanced controlling system have been used for effective and quality drying veneers.Heat Thermal Oil as a type of hot air boiler,which is environmental friendly and energy saving.The most advantages of plywood veneer dryer is achieve lowest drying cost and perfect drying effect.Advantages of Veneer Dryer Machine1. The well-developed heat exchange system fully improves the energy utilization rate and saves unnecessary energy waste.2.
Contact Now
The Continuous veneer mesh belt dryer is designed to handle the drying process of face veneer, back veneer and long core veneer. For process the surface veneer and long core veneer, this veneer dryer can avoid the break of the veneer, then can raise the veneer utilization ratio and production output. All outfitted air blower and screen are the high quality production, so it can increase the durability and useful life of the machine.
Contact Now
Veneer Jet DryerShine 2 deck veneer core dryer machine is widely valued for the lowest operation cost,high drying capacity,and energy-efficient as well as high-quality veneer output. It is meant for drying the Core Veneer & Face Veneer and is the Dryer of choice all over the country as well as abroad. The composite cost is only about $6-12/cubic meter fuel cost and electricity power.Standard wood veneer dryer is composed of heating chambers and cooling chambers. The veneer roller dryer allows automatic feeder devices, which can save labor costs greatly.
Contact Now
Roller Jet Veneer DryerThe Shine roller veneer dryer can make continuous feeding which can ensure the dryer keep working with no downtime. In this way, the drying efficiency is high and energy consumption is low for thin veneer dryer machine. The wood veneer drying machine is heated by a furnace/burner instead of steam boiler or thermal oil boiler. The core veneer dryer has the lowest drying cost as the biomass burner can directly burn all kinds of waste wood as the fuel. In addition, the double deck veneer dryer line has the salient features of high productivity, energ
Contact Now
Mesh Veneer DryerMesh veneer dryer is mainly used for the production of plywood. Compared with common plywood-veneer roller jet dryers, Plywood Face Veneer Drying Machine can dry thinner veneer 0.2-0.8mm. The quality requirements for the plywood face veneer drying line are also higher than the commercial veneer dryer. Plywood Veneer Dryer Machine is widely used in flatting drying of high-grade plywood, multi-layer board, and architectural core face veneer. The composite cost is only $6-12/cubic meter.
Contact Now
The mesh belt veneer dryer is an efficient and energy-saving wood drying equipment, mainly used for drying veneers, thin wood and other thin wood products. It achieves the ideal drying effect of veneers in a short time through uniform hot air flow and continuous mesh belt conveying.It realizes uniform drying of veneers and ensures that the humidity of veneers is controlled within the ideal range during the entire drying process.
Contact Now
Plywood Face Veneer Drying Machine Mesh belt net dryer consists of several independent unit sections. Mesh belt dryer is a closed-belt dryer. Its feature is that only the feed end and the discharge end are open, and the others are closed. Hot air flows through the equipment and the heat loss is low, which can save a lot of energy. The equipment is flexible in configuration, and there are many materials for drying at one time, and it can be continuously produced and dried, which is convenient to use and greatly reduces labor.
Contact Now
4 Deck Jet Roller Veneer DryerSHINE Roller veneer Dryer adopts the new axial flow fan, the whole machine power is reduced by Thirty-eight percent, low energy consumption, high output, the heat source can be selected according to the situation (biomass burner, thermal oil, natural gas, etc.), choose Shine to provide you with the best solution of low-cost veneer dryer.Advantages of Veneer Dryer Machine1. The well-developed heat exchange system fully improves the energy utilization rate and saves unnecessary energy waste.2. The control cabinet has automatic temperature control and spe
Contact Now
The veneer drying process consists of two parts: heating by blowing pipe and contact heating by upper and lower pressing rollers. Double heating improves heating efficiency. Both the hot air blower and the cold air blower of the veneer dryer adopt the new axial flow fan, which not only fully guarantees the air volume required for drying, but also reduces the total installed power by more than 38%, and minimizes the power consumption of the whole set of equipment. Diversified heat sources are available.
Contact Now
