Frequency Conversion Control Cabinet-manufacture,factory,supplier from China

The 40m 2 deck veneer dryer purchased by an Indonesian customer has now been installed and is being debugged.Due to the epidemic,we could not send someone to guide the installation.The customer successfully installed it in our video and chat communication instructions.Thank you very much for your support Our biomass burner,which can directly burn all kinds of waste wood,saves fuel efficiently; it adopts automatic control and frequency conversion control system,which can automatically adjust the transmission speed and To achieve the ideal drying effect,if you are interested in our machine,pleas

The 2 deck veneer dryer with biomass burner is currently in operation. It is used to dry rubber wood. It adopts full automatic control and frequency conversion control system. It can automatically adjust the transmission speed and temperature according to the thickness and moisture content of different veneers to achieve the ideal drying effect and accurately control the final moisture content. It avoids the phenomenon that a large number of veneers are over-dried or dried to meet the process requirements. The dried veneer is flat and wrinkle-free. We welcome you to visit the case site.

After the on-site drying test, the shrinkage rate of the veneer before and after drying by Shine veneer dryer is 2-2.5 cm, and the moisture content can be dried to zero, or it can be dried to the moisture you need according to your requirements. It adopts automatic control and frequency conversion control system, which can automatically adjust the transmission speed and temperature according to different veneer thickness and moisture content, so as to achieve the ideal drying effect. Biomass burners can directly burn all kinds of waste wood, saving drying costs.

The veneer dryer purchased by the South African customer has 4 deck of 50 meters and a width of 4.5 meters. It uses an automatic dialing machine, a semi-automatic dividing board machine and a collecting machine. It is equipped with our 15-ton biomass burner and can directly burn waste trees. It not only solves the problem of waste accumulation for customers, but also saves fuel costs for customers. The fully automatic control and frequency conversion control system can automatically adjust the transmission speed and temperature according to different veneer thickness and moisture content.

Faced with rising labor costs, finding highly automated solutions has become a customer demand. Are you also looking for highly automated solutions? Shine's fully automatic intelligent drying production line adopts fully automatic control and frequency conversion control systems. It automatically adjusts the speed and temperature according to the different thicknesses and moisture content of the veneer. It is equipped with fully automatic plate loading and closing devices, which can also be customized according to your actual situation. Customize your own plan!

In the face of rising labor costs, looking for highly automated solutions has become a customer demand, are you also looking for highly automated solutions? Shine fully automatic intelligent drying production line adopts fully automatic control and frequency conversion control system to automatically adjust the speed and temperature according to the different thickness and moisture content of the veneer. Exclusive plan! Bringing you an easier and more efficient drying process! Whether you pursue high automation or pay attention to manual operation, Shine can meet your needs.

Many people may encounter the problem of veneer jamming when using the roller veneer dryer. In order to avoid this problem, the following suggestions can be taken: First, keep the equipment clean, clean the dust collector and exhaust duct, and minimize the accumulation of dust; second, do a good job of adjusting the equipment, reduce the friction and wear of the equipment, and regularly check the status of the roller bearings; finally, pay attention to the control of drying temperature and humidity to avoid excessive temperature and humidity, which will cause veneer deformation and jamming.

Shine veneer dryers are available with outputs ranging from a dozen cubic meters to more than a hundred cubic meters. They have their own heat source biomass burner; they can directly burn waste bark to save fuel costs (it can also be used with other heat sources). The newly upgraded dryer reduces the power of the whole machine by 38%, achieving true energy saving. The automatic control system is adopted to automatically adjust the transmission speed and temperature according to different veneer thickness and moisture content to achieve the ideal drying effect.

During the drying process, the volume of the wood will shrink due to the loss of internal moisture, so the wood will shrink after drying. This is because after the moisture in the wood evaporates, the fibers in the wood become more compact, resulting in a reduction in the volume of the wood. In addition, the shrinkage rate of wood is also related to the type of wood, moisture content, drying method and other factors. Therefore, it is necessary to control the temperature and humidity during the drying process to avoid excessive shrinkage of the wood and affect its quality.

The 2 deck veneer dryer ordered by our customer has been produced and is being shipped. Our engineers will go to the site to guide the installation. The engineer will return only after guiding the equipment to operate normally. If you want to see the site, you can contact us in advance. We went to the customer's factory to visit and inspect. This equipment uses an axial flow fan, which reduces the power of the whole machine by 38%, achieving true energy saving. The burner can directly burn bark and black bark, saving fuel costs.